Thrust production and chordal flexion of the flukes of bottlenose dolphins performing tail stands at different efforts.

Dolphins have become famous for their ability to perform a wide variety of athletic and acrobatic behaviors including high-speed swimming, maneuverability, porpoising and tail stands. Tail stands are a behavior where part of the body is held vertically above the water's surface, achieved through thrust produced by horizontal tail fluke oscillations. Strong, efficient propulsors are needed to generate the force required to support the dolphin's body weight, exhibiting chordwise and spanwise flexibility throughout the stroke cycle. To determine how thrust production, fluke flexibility and tail stroke kinematics vary with effort, six adult bottlenose dolphins (Tursiops truncatus) were tested at three different levels based on the position of the center of mass (COM) relative to the water's surface: low (COM below surface), medium (COM at surface) and high (COM above surface) effort. Additionally, fluke flexibility was measured as a flex index (FI=chord length/camber length) at four points in the stroke cycle: center stroke up (CU), extreme top of stroke (ET), center stroke down (CD) and extreme bottom of stroke (EB). Video recordings were analyzed to determine the weight supported above the water (thrust production), peak-to-peak amplitude, stroke frequency and FI. Force production increased with low, medium and high efforts, respectively. Stroke frequency also increased with increased effort. Amplitude remained constant with a mean 33.8% of body length. Significant differences were seen in the FI during the stroke cycle. Changes in FI and stroke frequency allowed for increased force production with effort, and the peak-to-peak amplitude was higher compared with that for horizontal swimming.

Direct-reading instruments for aerosols: A review for occupational health and safety professionals part 1: Instruments and good practices.

With advances in technology, there are an increasing number of direct-reading instruments available to occupational health and safety professionals to evaluate occupational aerosol exposures. Despite the wide array of direct-reading instruments available to professionals, the adoption of direct-reading technology to monitor workplace exposures has been limited, partly due to a lack of knowledge on how the instruments operate, how to select an appropriate instrument, and challenges in data analysis techniques. This paper presents a review of direct-reading aerosol instruments available to occupational health and safety professionals, describes the principles of operation, guides instrument selection based on the workplace and exposure, and discusses data analysis techniques to overcome these barriers to adoption. This paper does not cover all direct-reading instruments for aerosols but only those that an occupational health and safety professional could use in a workplace to evaluate exposures. Therefore, this paper focuses on instruments that have the most potential for workplace use due to their robustness, past workplace use, and price with regard to return on investment. The instruments covered in this paper include those that measure aerosol number concentration, mass concentration, and aerosol size distributions.

Direct-reading instruments for aerosols: A review for occupational health and safety professionals part 2: Applications.

Direct reading instruments (DRIs) for aerosols have been used in industrial hygiene practice for many years, but their potential has not been fully realized by many occupational health and safety professionals. Although some DRIs quantify other metrics, this article will primarily focus on DRIs that measure aerosol number, size, or mass. This review addresses three applications of aerosol DRIs that occupational health and safety professionals can use to discern, characterize, and document exposure conditions and resolve aerosol-related problems in the workplace. The most common application of aerosol DRIs is the evaluation of engineering controls. Examples are provided for many types of workplaces and situations including construction, agriculture, mining, conventional manufacturing, advanced manufacturing (nanoparticle technology and additive manufacturing), and non-industrial sites. Aerosol DRIs can help identify the effectiveness of existing controls and, as needed, develop new strategies to reduce potential aerosol exposures. Aerosol concentration mapping (ACM) using DRI data can focus attention on emission sources in the workplace spatially illustrate the effectiveness of controls and constructively convey concerns to management and workers. Examples and good practices of ACM are included. Video Exposure Monitoring (VEM) is another useful technique in which video photography is synced with the concentration output of an aerosol DRI. This combination allows the occupational health and safety professional to see what tasks, environmental situations, and/or worker actions contribute to aerosol concentration and potential exposure. VEM can help identify factors responsible for temporal variations in concentration. VEM can assist with training, engage workers, convince managers about necessary remedial actions, and provide for continuous improvement of the workplace environment. Although using DRIs for control evaluation, ACM and VEM can be time-consuming, the resulting information can provide useful data to prompt needed action by employers and employees. Other barriers to adoption include privacy and security issues in some worksites. This review seeks to provide information so occupational health and safety professionals can better understand and effectively use these powerful applications of aerosol DRIs.

A 60:40 split: Differential mass support in dogs.

Dogs have been bred for different sizes and functions, which can affect their locomotor biomechanics. As quadrupeds, dogs must distribute their mass between fore and hind legs when standing. The mass distribution in dogs was studied to determine if the proportion of supported mass on each limb couplet is dependent on body size. A total of 552 dogs from 123 breeds ranging in size from Chihuahua to Mastiff were examined. Each dog was weighed on a digital scale while standing, alternating foreleg, and hind leg support. The overall "grand" mean proportion of mass on the forelegs to the total mass was 60.4% (range: 47.6-74.4%). The data set indicated no significant change in the ratio with total mass but there was a significant difference by sex. When separated into American Kennel Club categories, no group was notably different from the grand mean or from each other, but when sex was also considered, there was a significant difference that was not specifically discerned by post hoc analysis. The mean for female Hounds was notably below the grand mean. For clades based on genetics, the mean for European origin mastiffs was notably greater than the grand mean and significantly different from UK origin herders and coursers. The mass of the head, chest, and musculature for propulsion could explain the mass support differential. Mass distribution and terrestrial locomotion in dogs shows substantial variation among breeds.

Metalworking fluid mist--strategies to reduce exposure: a comparison of new and old transmission case transfer lines.

Three studies were performed to assess the effectiveness of various techniques to control metalworking fluid (MWF) mist. The studies consisted of a detailed main study that determined the effect of degree of enclosure on personal exposures and area concentrations of MWF mist on two machining transfer lines. One ancillary study was conducted to determine the effect of shutting off MWF delivery during down time; the second ancillary study investigated the effectiveness of improved retrofitted enclosure. In the main study, the two operations were identical except for degree of enclosure. Personal and area sampling results for the new line were about half those found in the old line. Measurements at the new operation exhibited significantly less variability. Personal exposures and area concentrations were significantly less at the new operation than at the older, less enclosed operation, demonstrating that the total enclosure in the new operation provides better and more consistent control of the mist. The first ancillary study was conducted to determine if shutting off MWF delivery to the parts being machined reduced area MWF mist concentration during downtime at a partially enclosed transfer machining line. A significant reduction in concentration of 80% was measured with machining off/MWF off. Mist concentrations measured with machining off/MWF on were not significantly different from mist levels measured during machining on/MWF on. The second ancillary study investigated the reduction of mist concentration achieved through improved enclosure of an existing set of machines. Area mist concentrations were measured at a machining operation before and after the installation of an improved enclosure. Area mist concentrations were reduced by 87% with the improved enclosure.